无梁板式高桩码头温度效应分析

气温的年变化会引起结构内温度的均匀变化,从而使得结构内部产生变形和内力,在高桩码头工程中温度作用往往会引起不利影响。为了研究无梁板式高桩码头的温度效应,基于无限板的热传导规律,以工程实例为依托,利用有限元软件ABAQUS建立三维模型。结合杭州地区的逐时气象资料,研究了气温变化特征、面板温差场以及结构变形与位移的变化规律,并对基本气温的选取进行讨论。结果表明:气温在无梁面板中呈现以厚度方向为主的一维传热特征,温度场在水平向分布均匀;气温年变幅在面板内几无衰减,日变幅对面板温度影响不可忽略;面板的整体温差与竣工时气温和年平均气温差,以及年变幅、日变幅的衰减值有关;无梁板码头基桩的温度响应受面板的整体温差控制,两者瞬时同步变化。     

桥梁单板受力的原因及预防措施探讨

从宏观角度分析桥梁预制板单板受力的一般规律,以及形成单板受力的原因,并从设计角度提出克服单板受力的措施,尤其是提出设置横向预应力是解决单板受力的有效措施,可供设计人员参考.     

斜向波浪对斜坡堤胸墙作用力的试验研究

斜坡堤胸墙的稳定性主要受到波浪作用的影响,而且实际工程中斜坡堤多受斜向波浪作用。通过斜向与正向不规则波对斜坡堤胸墙作用的物理模型试验研究,分析斜坡堤单个胸墙所受的斜向波浪总力的折减系数随水位和波浪入射角度的变化规律,并与斜向波浪对单元直立堤的作用情况进行对比。结果表明:斜坡堤单个胸墙所受的斜向波浪总力的折减系数总体上随着水位的降低而变小,随着波浪入射角度的减小而变小;斜向波浪总浮托力的折减系数一般小于总水平力的折减系数;在不同水位和波浪入射角下,斜坡堤单个胸墙所受的斜向波浪总力的折减系数与单元直立堤有一定差别。     

船用质谱仪电磁兼容结构设计

船用质谱仪作为舰艇舱室气体测量的主要设备,其电磁兼容性能的好坏直接关系到舰艇舱室环境检测的准确性,对艇员的正常生活和工作,甚至舰艇的作战能力都会产生很大的影响.本文依据电磁兼容的基本原理,从屏蔽和线缆敷设2个方面对船用质谱仪进行电磁兼容结构设计,使仪器满足GJB151B《军用设备和分系统电磁发射和敏感度要求》的相关规定,从而保证仪器在复杂的电磁环境下测量的准确度、可靠性和稳定性.     

浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

基于虚拟应力场法的船舶避让与控制

为了实现船舶在航道内的避障,应用虚拟力场法建立了避障模型,描述了目标点的虚拟引力和障碍物的虚拟斥力之间的关系及其功能设计,实现了从船舶运动坐标值到控制量的转变,结果证明．船舶能够在多变的周边环境中实现避障功能。     

大倾角搁浅船舶扳正过程分析

在研究大倾角搁浅船舶的扳正过程中,计算了难船扳正力、横倾角和吃水。根据搁浅船舶的受力特点,建立了其力学模型,分析了扳正过程中横倾角、吃水、入泥深度与海底泥土性质对船体的影响。利用GHS软件模拟搁浅船舶的扳正过程,以某搁浅液化气船舶为例,求解了其扳正过程中船体扳正力、总搁坐力、剪力、弯矩和转矩,比较了难船不同扳正方案,分析了难船的扳正方式、搁坐位置、上层建筑与储气罐对难船打捞的影响。分析结果表明:在扳正过程中,3个方案的力学参数的变化趋势是一致的。最大扳正力相差较大,差值为9.1%~20.0%。搁坐力、剪力和弯矩均在横倾角为-55°~-50°时达到最大值,船体虽然在该阶段不需加载较大的扳正力,但仍应该注意船体的受力情况。在横倾角为-120°~-100°时,转矩变化非常剧烈。弯矩和转矩均出现了反向变化的现象,威胁船体结构的安全,扳正中应该谨慎处理。选择合适的扳正方案时应该综合考虑扳正力施力点的位置和扳正过程对船体与环境安全的潜在威胁。     

带分布式动力吸振器基座振动传递特性研究

在弹性梁上等间距安装吸振器,构建带分布式动力器的基座系统,建立了Euler梁-吸振器-弹性支承耦合系统的力学模型。给出了子结构的导纳矩阵,推导了基座的动态特性传递方程,得到了基座系统的力传递率表达式,并详细讨论了系统参数对基座减振性能的影响。搭建了带分布式吸振器基座系统实验平台,对电阻应变式力传感器进行了标定,测试了基座的力传递率特性。数值仿真与实验测试结果均表明,带分布式动力吸振器基座在低频取得了优越的减振效果。